Текущее время: 29 апр 2024, 04:37 • Часовой пояс: UTC + 3 часа |
Тюнер H7
Автор | Сообщение |
hikkikamori
|
Добавлено: 03 ноя 2011, 11:35. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 02 ноя 2011, 00:23 Сообщения: 8
|
Поставил новое ядро 3.0.4 , тюнер начал определятся Код: [ 5.723529] saa7130/34: v4l2 driver version 0.2.16 loaded [ 5.723651] saa7134 0000:02:07.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 5.723656] saa7133[0]: found at 0000:02:07.0, rev: 209, irq: 22, latency: 64, mmio: 0xfbffb800 [ 5.723662] saa7133[0]: subsystem: 5ace:7190, board: Beholder BeholdTV H7 [card=178,autodetected] [ 5.723716] saa7133[0]: board init: gpio is 0 [ 5.723718] saa7133[0]/core: hwinit1 [ 5.723727] saa7133[0]: gpio: mode=0x0000000 in=0x0000000 out=0x0000000 [pre-init] [ 5.872059] saa7133[0]: i2c eeprom 00: ce 5a 90 71 54 20 00 00 00 00 00 00 00 00 00 01 [ 5.872066] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872071] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872077] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872082] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872087] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872092] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872097] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872102] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872107] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872112] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872117] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872122] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872127] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872132] saa7133[0]: i2c eeprom e0: d8 cf 00 00 ff ff ff ff ff ff ff ff ff ff ff ff [ 5.872137] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff [ 5.880061] saa7133[0]: i2c scan: found device @ 0x1e [???] [ 5.892061] saa7133[0]: i2c scan: found device @ 0x5a [remote control] [ 5.904054] saa7133[0]: i2c scan: found device @ 0xa0 [eeprom] [ 5.912059] saa7133[0]: i2c scan: found device @ 0xc2 [???] [ 5.992802] IR NEC protocol handler initialized [ 6.046495] i2c-core: driver [tuner] using legacy suspend method [ 6.046497] i2c-core: driver [tuner] using legacy resume method [ 6.046801] IR RC5(x) protocol handler initialized [ 6.052108] tuner 1-0061: Tuner -1 found with type(s) Radio TV. [ 6.133797] IR RC6 protocol handler initialized [ 6.212031] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 6.275597] IR JVC protocol handler initialized [ 6.290453] xc5000 1-0061: creating new instance [ 6.296063] xc5000: Successfully identified at address 0x61 [ 6.296065] xc5000: Firmware has not been loaded previously [ 6.296068] saa7133[0]/core: hwinit2 Звука нет, с штатной антенной ничего не находит ни mplayer, ни tvtime - это что касается tv Радио каналы вроде как находит, но опять таки звука нет Подскажите какая позиция из этого списка http://www.mjmwired.net/kernel/Documentation/video4linux/CARDLIST.tuner подходит для этой модели тюнера? В syslog выскакивает ошибка следующего содержания: Код: Nov 3 03:23:15 debian kernel: [ 7.084332] saa7133[0]: dsp access error
|
|
|
hikkikamori
|
Добавлено: 04 ноя 2011, 09:05. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 02 ноя 2011, 00:23 Сообщения: 8
|
Осталось решить проблему со звуком... вот конфиг behold.conf из /etc/modprobe.d Код: options xc5000 no_poweroff=1 options saa7134 i2c_scan=1 radio_nr=1 gbuffers=4 alsa=1 secam=d параметр alsa=1 не помагает решить проблему с передачей звука по pci шине вот часть dmesg: Код: [ 5.820653] Linux video capture interface: v2.00 [ 5.871292] saa7130/34: v4l2 driver version 0.2.16 loaded [ 5.871411] saa7134 0000:02:07.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 5.871417] saa7133[0]: found at 0000:02:07.0, rev: 209, irq: 22, latency: 64, mmio: 0xfbffb800 [ 5.871423] saa7133[0]: subsystem: 5ace:7190, board: Beholder BeholdTV H7 [card=178,autodetected] [ 5.871485] saa7133[0]: board init: gpio is 0 [ 5.886067] AMD64 EDAC driver v3.4.0 [ 5.886174] EDAC amd64: DRAM ECC disabled. [ 5.886181] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load. [ 5.886182] Either enable ECC checking or force module loading by setting 'ecc_enable_override'. [ 5.886184] (Note that use of the override may cause unknown side effects.) [ 6.020058] saa7133[0]: i2c eeprom 00: ce 5a 90 71 54 20 00 00 00 00 00 00 00 00 00 01 [ 6.020065] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020071] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020076] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020081] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020086] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020091] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020096] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020101] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020106] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020111] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020116] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020121] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020126] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020131] saa7133[0]: i2c eeprom e0: d8 cf 00 00 ff ff ff ff ff ff ff ff ff ff ff ff [ 6.020136] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff [ 6.028060] saa7133[0]: i2c scan: found device @ 0x1e [???] [ 6.040039] saa7133[0]: i2c scan: found device @ 0x5a [remote control] [ 6.052060] saa7133[0]: i2c scan: found device @ 0xa0 [eeprom] [ 6.060062] saa7133[0]: i2c scan: found device @ 0xc2 [???] [ 6.157210] IR NEC protocol handler initialized [ 6.427477] i2c-core: driver [tuner] using legacy suspend method [ 6.427479] i2c-core: driver [tuner] using legacy resume method [ 6.436100] tuner 1-0061: Tuner -1 found with type(s) Radio TV. [ 6.473202] IR RC5(x) protocol handler initialized [ 6.538266] xc5000 1-0061: creating new instance [ 6.544061] xc5000: Successfully identified at address 0x61 [ 6.544064] xc5000: Firmware has not been loaded previously [ 6.591785] IR RC6 protocol handler initialized [ 6.664378] IR JVC protocol handler initialized [ 6.674987] IR Sony protocol handler initialized [ 6.781990] lirc_dev: IR Remote Control driver registered, major 251 [ 6.791509] IR LIRC bridge handler initialized [ 6.820893] scsi 8:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0 [ 6.821414] scsi 8:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0 [ 6.822035] scsi 8:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0 [ 6.822661] scsi 8:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0 [ 6.823257] sd 8:0:0:0: Attached scsi generic sg4 type 0 [ 6.823393] sd 8:0:0:1: Attached scsi generic sg5 type 0 [ 6.823868] sd 8:0:0:2: Attached scsi generic sg6 type 0 [ 6.824337] sd 8:0:0:3: Attached scsi generic sg7 type 0 [ 6.834102] sd 8:0:0:0: [sdd] Attached SCSI removable disk [ 6.835475] sd 8:0:0:3: [sdg] Attached SCSI removable disk [ 6.836856] sd 8:0:0:1: [sde] Attached SCSI removable disk [ 6.838464] sd 8:0:0:2: [sdf] Attached SCSI removable disk [ 6.891838] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 7.059330] HDA Intel 0000:04:00.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 7.059333] hda_intel: Disabling MSI [ 7.059381] HDA Intel 0000:04:00.1: setting latency timer to 64 [ 7.114577] nvidia: module license 'NVIDIA' taints kernel. [ 7.114580] Disabling lock debugging due to kernel taint [ 7.840057] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0 [ 7.928057] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0 [ 8.016063] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0 [ 8.104062] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0 [ 8.232228] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:02.0/0000:04:00.1/sound/card1/input6 [ 8.232281] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:02.0/0000:04:00.1/sound/card1/input7 [ 8.232328] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:02.0/0000:04:00.1/sound/card1/input8 [ 8.232375] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:02.0/0000:04:00.1/sound/card1/input9 [ 8.233898] nvidia 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 8.233905] nvidia 0000:04:00.0: setting latency timer to 64 [ 8.233909] vgaarb: device changed decodes: PCI:0000:04:00.0,olddecodes=io+mem,decodes=none:owns=io+mem [ 8.234051] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 280.13 Wed Jul 27 16:53:56 PDT 2011 [ 31.148063] Registered IR keymap rc-behold [ 31.148141] input: i2c IR (BeholdTV) as /devices/virtual/rc/rc0/input10 [ 31.148192] rc0: i2c IR (BeholdTV) as /devices/virtual/rc/rc0 [ 31.148194] ir-kbd-i2c: i2c IR (BeholdTV) detected at i2c-1/1-002d/ir0 [saa7133[0]] [ 31.148430] saa7133[0]: registered device video0 [v4l2] [ 31.148449] saa7133[0]: registered device vbi0 [ 31.148467] saa7133[0]: registered device radio1 [ 31.161261] dvb_init() allocating 1 frontend [ 31.176060] xc5000 1-0061: attaching existing instance [ 31.184057] xc5000: Successfully identified at address 0x61 [ 31.184059] xc5000: Firmware has not been loaded previously [ 31.184063] DVB: registering new adapter (saa7133[0]) [ 31.184066] DVB: registering adapter 0 frontend 0 (Zarlink ZL10353 DVB-T)... [ 31.224061] xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)... [ 31.269590] xc5000: firmware read 12401 bytes. [ 31.269592] xc5000: firmware uploading... [ 31.276177] xc5000: I2C read failed [ 31.276179] xc5000: xc_SetSignalSource(1) failed [ 31.276335] zl10353: write to reg 50 failed (err = -5)! [ 31.276479] zl10353: write to reg 50 failed (err = -5)! [ 31.286668] saa7134 ALSA driver for DMA sound loaded [ 31.286694] saa7133[0]/alsa: saa7133[0] at 0xfbffb800 irq 22 registered as card -1 [ 36.252052] xc5000: firmware upload complete... [ 36.261147] xc5000: I2C write failed (len=4) [ 36.261175] xc5000: I2C read failed [ 36.364588] xc5000: I2C write failed (len=4) [ 36.885875] Adding 2891632k swap on /dev/sdc6. Priority:-1 extents:1 across:2891632k [ 37.309467] EXT3-fs (sdc1): using internal journal [ 37.379211] loop: module loaded [ 39.118504] EXT4-fs (sdb5): mounted filesystem with ordered data mode. Opts: (null) [ 39.128841] EXT3-fs: barriers not enabled [ 39.129054] kjournald starting. Commit interval 5 seconds [ 39.129443] EXT3-fs (sda5): using internal journal [ 39.129448] EXT3-fs (sda5): mounted filesystem with ordered data mode [ 39.242832] EXT3-fs: barriers not enabled [ 39.260401] kjournald starting. Commit interval 5 seconds [ 39.260693] EXT3-fs (sdc5): using internal journal [ 39.260697] EXT3-fs (sdc5): mounted filesystem with ordered data mode [ 40.858564] r8169 0000:01:00.0: eth0: unable to load firmware patch rtl_nic/rtl8168e-2.fw (-2) [ 40.883677] r8169 0000:01:00.0: eth0: link down [ 40.883682] r8169 0000:01:00.0: eth0: link down [ 40.884648] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 41.182742] fuse init (API version 7.16) [ 42.502186] r8169 0000:01:00.0: eth0: link up [ 42.503106] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 47.400678] Bluetooth: Core ver 2.16 [ 47.400695] NET: Registered protocol family 31 [ 47.400697] Bluetooth: HCI device and connection manager initialized [ 47.400699] Bluetooth: HCI socket layer initialized [ 51.260658] lp: driver loaded but no devices found [ 51.469356] ppdev: user-space parallel port driver [ 52.488795] parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff [ 52.488801] parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff [ 52.488803] parport 0x378: You gave this address, but there is probably no parallel port there! [ 52.488819] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 52.584039] eth0: no IPv6 routers present [ 52.584190] lp0: using parport0 (interrupt-driven). [ 57.101118] xc5000: I2C write failed (len=4) [ 57.101133] xc5000: I2C write failed (len=4) [ 57.101666] xc5000: I2C read failed [ 63.950925] powernow-k8: Found 1 AMD Athlon(tm) II X2 245 Processor (2 cpu cores) (version 2.20.00) [ 63.950956] powernow-k8: 0 : pstate 0 (2900 MHz) [ 63.950958] powernow-k8: 1 : pstate 1 (2200 MHz) [ 63.950959] powernow-k8: 2 : pstate 2 (1700 MHz) [ 63.950961] powernow-k8: 3 : pstate 3 (800 MHz) При загрузке системы долго (чуть меньше минуты) ждёт на строчке: Waiting for /dev to be fully populated потом выдаёт: xc5000: xc_SetTVStandard failed xc5000: I2C write failed (len=4) xc5000: I2C write failed (len=4) после как обычно. Код: cat /var/log/syslog |grep failed ....... Nov 4 08:36:54 debian kernel: [ 31.280203] xc5000: I2C read failed Nov 4 08:36:54 debian kernel: [ 31.280206] xc5000: xc_SetSignalSource(1) failed Nov 4 08:36:59 debian bluetoothd[1732]: Server initialization failed Nov 4 08:37:09 debian kernel: [ 55.636217] xc5000: I2C read failed Nov 4 08:37:09 debian kernel: [ 55.636220] xc5000: xc_SetSignalSource(1) failed Nov 4 08:37:09 debian kernel: [ 55.636374] xc5000: I2C read failed Nov 4 08:37:09 debian kernel: [ 55.860536] xc5000: I2C write failed (len=64) Nov 4 08:37:09 debian kernel: [ 55.864196] xc5000: I2C read failed Nov 4 08:38:35 debian kernel: [ 141.425175] xc5000: I2C write failed (len=4) Nov 4 08:38:35 debian kernel: [ 141.532093] xc5000: I2C write failed (len=4) Nov 4 08:38:35 debian kernel: [ 141.532720] xc5000: I2C read failed Nov 4 08:38:35 debian kernel: [ 141.532728] xc5000: I2C read failed Nov 4 09:01:36 debian kernel: [ 1522.228756] xc5000: I2C write failed (len=4) Nov 4 09:01:36 debian kernel: [ 1522.228765] xc5000: xc_SetTVStandard failed Nov 4 09:01:44 debian kernel: [ 1530.544780] xc5000: I2C write failed (len=4) Nov 4 09:01:44 debian kernel: [ 1530.544789] xc5000: xc_SetTVStandard failed Nov 4 09:01:52 debian kernel: [ 1538.852774] xc5000: I2C write failed (len=4) Nov 4 09:01:52 debian kernel: [ 1538.852782] xc5000: xc_SetTVStandard failed Nov 4 09:02:40 debian kernel: [ 1586.272759] xc5000: I2C write failed (len=4) Nov 4 09:02:40 debian kernel: [ 1586.272767] xc5000: xc_SetTVStandard failed Nov 4 09:02:48 debian kernel: [ 1594.488741] xc5000: I2C write failed (len=4) Nov 4 09:02:48 debian kernel: [ 1594.488744] xc5000: xc_SetTVStandard failed Nov 4 09:02:56 debian kernel: [ 1602.712774] xc5000: I2C write failed (len=4) Nov 4 09:02:56 debian kernel: [ 1602.712782] xc5000: xc_SetTVStandard failed Nov 4 09:03:05 debian kernel: [ 1611.000790] xc5000: I2C write failed (len=4) Nov 4 09:03:05 debian kernel: [ 1611.000798] xc5000: xc_SetTVStandard failed Nov 4 09:03:13 debian kernel: [ 1619.200774] xc5000: I2C write failed (len=4) Nov 4 09:03:13 debian kernel: [ 1619.200782] xc5000: xc_SetTVStandard failed Nov 4 09:03:21 debian kernel: [ 1627.508746] xc5000: I2C write failed (len=4) Nov 4 09:03:21 debian kernel: [ 1627.508749] xc5000: xc_SetTVStandard failed Nov 4 09:03:55 debian kernel: [ 1661.004759] xc5000: I2C write failed (len=4) Nov 4 09:03:55 debian kernel: [ 1661.004767] xc5000: xc_SetTVStandard failed Nov 4 09:04:03 debian kernel: [ 1669.220793] xc5000: I2C write failed (len=4) Nov 4 09:04:03 debian kernel: [ 1669.220801] xc5000: xc_SetTVStandard failed Nov 4 09:04:11 debian kernel: [ 1677.484755] xc5000: I2C write failed (len=4) Nov 4 09:04:11 debian kernel: [ 1677.484763] xc5000: xc_SetTVStandard failed Nov 4 09:04:36 debian kernel: [ 1702.236788] xc5000: I2C write failed (len=4) Nov 4 09:04:36 debian kernel: [ 1702.236797] xc5000: xc_SetTVStandard failed Nov 4 09:06:17 debian kernel: [ 31.276177] xc5000: I2C read failed Nov 4 09:06:17 debian kernel: [ 31.276179] xc5000: xc_SetSignalSource(1) failed Nov 4 09:06:17 debian kernel: [ 31.276335] zl10353: write to reg 50 failed (err = -5)! Nov 4 09:06:17 debian kernel: [ 31.276479] zl10353: write to reg 50 failed (err = -5)! Nov 4 09:06:17 debian kernel: [ 36.261147] xc5000: I2C write failed (len=4) Nov 4 09:06:17 debian kernel: [ 36.261175] xc5000: I2C read failed Nov 4 09:06:17 debian kernel: [ 36.364588] xc5000: I2C write failed (len=4) Nov 4 09:06:22 debian bluetoothd[1736]: Server initialization failed Nov 4 09:06:32 debian kernel: [ 57.101118] xc5000: I2C write failed (len=4) Nov 4 09:06:32 debian kernel: [ 57.101133] xc5000: I2C write failed (len=4) Nov 4 09:06:32 debian kernel: [ 57.101666] xc5000: I2C read failed Nov 4 09:52:24 debian kernel: [ 31.488209] xc5000: I2C read failed Nov 4 09:52:24 debian kernel: [ 31.488213] xc5000: xc_SetTVStandard failed Nov 4 09:52:24 debian kernel: [ 31.488372] zl10353: write to reg 50 failed (err = -5)! Nov 4 09:52:24 debian kernel: [ 31.488517] zl10353: write to reg 50 failed (err = -5)! Nov 4 09:52:24 debian kernel: [ 36.473150] xc5000: I2C write failed (len=4) Nov 4 09:52:24 debian kernel: [ 36.473176] xc5000: I2C read failed Nov 4 09:52:24 debian kernel: [ 36.576600] xc5000: I2C write failed (len=4) Nov 4 09:52:28 debian bluetoothd[2265]: Server initialization failed Nov 4 09:52:36 debian kernel: [ 242.017149] xc5000: I2C write failed (len=4) Nov 4 09:52:36 debian kernel: [ 242.017177] xc5000: I2C write failed (len=4) Nov 4 09:52:36 debian kernel: [ 242.017900] xc5000: I2C read failed Что делать? ![Что? :huh:](./images/smilies/icon_question.gif)
|
|
|
hikkikamori
|
Добавлено: 04 ноя 2011, 23:53. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 02 ноя 2011, 00:23 Сообщения: 8
|
up добавил параметр debug=1 в xc:5000 теперь dmesg выдает следующее: Код: [ 6.018747] Linux video capture interface: v2.00 [ 6.258217] saa7130/34: v4l2 driver version 0.2.16 loaded [ 6.258461] saa7134 0000:02:07.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 6.258465] saa7133[0]: setting pci latency timer to 32 [ 6.258470] saa7133[0]: found at 0000:02:07.0, rev: 209, irq: 22, latency: 32, mmio: 0xfbffb800 [ 6.258476] saa7133[0]: subsystem: 5ace:7190, board: Beholder BeholdTV H7 [card=178,insmod option] [ 6.258539] saa7133[0]: board init: gpio is 0 [ 6.280775] IR NEC protocol handler initialized [ 6.408045] saa7133[0]: i2c eeprom 00: ce 5a 90 71 54 20 00 00 00 00 00 00 00 00 00 01 [ 6.408052] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408057] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408062] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408067] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408072] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408077] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408082] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408087] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408092] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408098] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408103] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408108] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408113] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408118] saa7133[0]: i2c eeprom e0: d8 cf 00 00 ff ff ff ff ff ff ff ff ff ff ff ff [ 6.408123] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff [ 6.416398] IR RC5(x) protocol handler initialized ...... [ 6.856840] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 6.869971] xc5000: xc5000_attach(1-0061) [ 6.869974] xc5000 1-0061: creating new instance [ 6.876060] xc5000: Successfully identified at address 0x61 [ 6.876063] xc5000: Firmware has not been loaded previously [ 6.884187] xc5000: xc5000_is_firmware_loaded() returns True id = 0x20 [ 6.884190] xc5000: xc5000_set_tv_freq() frequency=6400 (in units of 62.5khz) [ 6.884192] xc5000: xc_SetSignalSource(1) Source = CABLE [ 6.896600] nvidia: module license 'NVIDIA' taints kernel. [ 6.896602] Disabling lock debugging due to kernel taint [ 7.113762] lirc_dev: IR Remote Control driver registered, major 251 [ 7.123291] IR LIRC bridge handler initialized ............. [ 8.296331] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:02.0/0000:04:00.1/sound/card1/input8 [ 8.296378] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:02.0/0000:04:00.1/sound/card1/input9 [ 9.140057] xc5000: xc_SetTVStandard(0x8049,0x0c04) [ 9.140060] xc5000: xc_SetTVStandard() Standard = B/G-PAL-NICAM [ 15.164056] xc5000: xc_tune_channel(400000000) [ 15.164058] xc5000: xc_set_RF_frequency(400000000) [ 17.304062] xc5000: *** ADC envelope (0-1023) = 1798 [ 17.312064] xc5000: *** Frequency error = 49796 Hz [ 17.320057] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 27390 [ 17.336057] xc5000: *** HW: V00.00, FW: V00.00.0000 [ 17.344062] xc5000: *** Horizontal sync frequency = 7332 Hz [ 17.352066] xc5000: *** Frame lines = 50132 [ 17.360056] xc5000: *** Quality (0:<8dB, 7:>56dB) = 0 [ 17.368057] xc5000: xc5000_is_firmware_loaded() returns False id = 0x2000 [ 17.376057] xc5000: xc5000_is_firmware_loaded() returns True id = 0x20 [ 17.376059] xc5000: xc_initialize() [ 21.496059] xc5000: xc5000_set_tv_freq() frequency=6400 (in units of 62.5khz) [ 21.496062] xc5000: xc_SetSignalSource(1) Source = CABLE [ 23.504056] xc5000: xc_SetTVStandard(0x8049,0x0c04) [ 23.504059] xc5000: xc_SetTVStandard() Standard = B/G-PAL-NICAM [ 29.528056] xc5000: xc_tune_channel(400000000) [ 29.528059] xc5000: xc_set_RF_frequency(400000000) [ 31.668063] xc5000: *** ADC envelope (0-1023) = 1798 [ 31.676062] xc5000: *** Frequency error = 805687 Hz [ 31.684064] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 45568 [ 31.700062] xc5000: *** HW: V00.00, FW: V00.00.0030 [ 31.708062] xc5000: *** Horizontal sync frequency = 1976 Hz [ 31.716057] xc5000: *** Frame lines = 54527 [ 31.724056] xc5000: *** Quality (0:<8dB, 7:>56dB) = 0 [ 31.776043] Registered IR keymap rc-behold [ 31.776126] input: i2c IR (BeholdTV) as /devices/virtual/rc/rc0/input10 [ 31.776173] rc0: i2c IR (BeholdTV) as /devices/virtual/rc/rc0 [ 31.776175] ir-kbd-i2c: i2c IR (BeholdTV) detected at i2c-1/1-002d/ir0 [saa7133[0]] [ 31.776542] xc5000: xc5000_sleep() [ 31.776599] saa7133[0]: registered device video0 [v4l2] [ 31.776620] saa7133[0]: registered device vbi0 [ 31.776636] saa7133[0]: registered device radio0 [ 31.796052] xc5000: xc5000_is_firmware_loaded() returns False id = 0x2000 [ 31.804069] xc5000: xc5000_is_firmware_loaded() returns True id = 0x20 [ 31.804072] xc5000: xc5000_set_radio_freq() frequency=1400000 (in units of khz) [ 31.804074] xc5000: xc5000_set_radio_freq() radio input not configured [ 31.804125] xc5000: xc5000_sleep() [ 31.812056] xc5000: xc5000_is_firmware_loaded() returns False id = 0x2000 [ 31.817918] dvb_init() allocating 1 frontend [ 31.820066] xc5000: xc5000_is_firmware_loaded() returns True id = 0x20 [ 31.820069] xc5000: xc_initialize() [ 31.828063] xc5000: xc5000_is_firmware_loaded() returns False id = 0x2000 [ 31.828066] xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)... [ 31.829149] xc5000: I2C write failed (len=4) [ 31.829177] zl10353_read_register: readreg error (reg=127, ret==-5) [ 31.829184] saa7133[0]/dvb: frontend initialization failed [ 31.868738] saa7134 ALSA driver for DMA sound loaded [ 31.868764] saa7133[0]/alsa: saa7133[0] at 0xfbffb800 irq 22 registered as card -1 [ 31.871588] xc5000: firmware read 12401 bytes. [ 31.871590] xc5000: firmware uploading... [ 31.871592] xc5000: xc5000_TunerReset() [ 34.368051] xc5000: Unable to load firmware and init tuner [ 34.368178] xc5000: xc5000_sleep() [ 36.016058] xc5000: firmware upload complete... [ 36.016068] xc5000: xc_initialize() [ 36.212058] xc5000: xc5000_set_tv_freq() frequency=6400 (in units of 62.5khz) [ 36.212061] xc5000: xc_SetSignalSource(1) Source = CABLE [ 36.228064] xc5000: xc_SetTVStandard(0x8049,0x0c04) [ 36.228067] xc5000: xc_SetTVStandard() Standard = B/G-PAL-NICAM [ 36.276064] xc5000: xc_tune_channel(400000000) [ 36.276066] xc5000: xc_set_RF_frequency(400000000) [ 36.844063] xc5000: *** ADC envelope (0-1023) = 956 [ 36.852057] xc5000: *** Frequency error = 0 Hz [ 36.860057] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 2 [ 36.876064] xc5000: *** HW: V03.02, FW: V01.06.0072 [ 36.884065] xc5000: *** Horizontal sync frequency = 15931 Hz [ 36.892057] xc5000: *** Frame lines = 65535 [ 36.900056] xc5000: *** Quality (0:<8dB, 7:>56dB) = 0 [ 36.900164] xc5000: xc5000_sleep() ..................................... .................... [ 58.276026] xc5000: xc5000_is_firmware_loaded() returns True id = 0x1388 [ 58.276030] xc5000: xc5000_set_radio_freq() frequency=1400000 (in units of khz) [ 58.276032] xc5000: xc5000_set_radio_freq() radio input not configured [ 58.276563] xc5000: xc5000_sleep() [ 58.284067] xc5000: xc5000_is_firmware_loaded() returns True id = 0x1388 [ 58.284071] xc5000: xc5000_set_tv_freq() frequency=6400 (in units of 62.5khz) [ 58.284073] xc5000: xc_SetSignalSource(1) Source = CABLE [ 58.292071] xc5000: xc5000_is_firmware_loaded() returns True id = 0x1388 [ 58.292075] xc5000: xc5000_set_tv_freq() frequency=6400 (in units of 62.5khz) [ 58.292077] xc5000: xc_SetSignalSource(1) Source = CABLE [ 58.316072] xc5000: xc_SetTVStandard(0x8049,0x0c04) [ 58.316074] xc5000: xc_SetTVStandard() Standard = B/G-PAL-NICAM [ 58.324057] xc5000: xc_SetTVStandard(0x8049,0x0c04) [ 58.324060] xc5000: xc_SetTVStandard() Standard = B/G-PAL-NICAM [ 58.412056] xc5000: xc_tune_channel(400000000) [ 58.412059] xc5000: xc_set_RF_frequency(400000000) [ 58.420048] xc5000: xc_tune_channel(400000000) [ 58.420051] xc5000: xc_set_RF_frequency(400000000) [ 58.433152] xc5000: I2C write failed (len=4) [ 58.433177] xc5000: I2C read failed [ 58.544046] xc5000: *** ADC envelope (0-1023) = 108 [ 58.552066] xc5000: *** ADC envelope (0-1023) = 88 [ 58.560055] xc5000: *** Frequency error = 0 Hz [ 58.568069] xc5000: *** Frequency error = 0 Hz [ 58.576055] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 0 [ 58.584047] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 0 [ 58.608065] xc5000: *** HW: V03.02, FW: V01.06.0072 [ 58.616055] xc5000: *** HW: V03.02, FW: V01.06.0072 [ 58.624059] xc5000: *** Horizontal sync frequency = 16206 Hz [ 58.632051] xc5000: *** Horizontal sync frequency = 16076 Hz [ 58.640063] xc5000: *** Frame lines = 65535 [ 58.648055] xc5000: *** Frame lines = 689 [ 58.656061] xc5000: *** Quality (0:<8dB, 7:>56dB) = 5 [ 58.664051] xc5000: *** Quality (0:<8dB, 7:>56dB) = 1 [ 59.787472] xc5000: xc5000_sleep() [ 59.787857] xc5000: xc5000_sleep()
|
|
|
hikkikamori
|
Добавлено: 05 ноя 2011, 02:00. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 02 ноя 2011, 00:23 Сообщения: 8
|
При запуске tvtime в dmesg появляется следующее: Код: [ 2045.080079] xc5000: *** Frequency error = 1023968 Hz [ 2045.432090] xc5000: *** Frequency error = 1023968 Hz [ 2045.796054] xc5000: *** Frequency error = 1023968 Hz [ 2046.224073] xc5000: *** Frequency error = 1023968 Hz [ 2046.596097] xc5000: *** Frequency error = 1023968 Hz [ 2047.044075] xc5000: *** Frequency error = 1023968 Hz [ 2049.444048] xc5000: *** Frequency error = 734 Hz [ 2049.976079] xc5000: *** Frequency error = 15 Hz [ 2053.068094] xc5000: *** Frequency error = 15 Hz [ 2053.496085] xc5000: *** Frequency error = 15 Hz [ 2053.900079] xc5000: *** Frequency error = 15 Hz [ 2054.396077] xc5000: *** Frequency error = 15 Hz [ 2054.808078] xc5000: *** Frequency error = 15 Hz [ 2055.316061] xc5000: *** Frequency error = 15 Hz [ 2057.456053] xc5000: *** Frequency error = 734 Hz [ 2058.576089] xc5000: *** Frequency error = 15 Hz [ 2059.760098] xc5000: *** Frequency error = 1023968 Hz видео по прежнему есть, звука - нет Если использовать этот скрипт: Код: hikkikamori@debian:~$ cat /media/local_disk1/.install/Скрипты/tv-tuner/tvtime.sh #!/bin/sh if [ -f /usr/bin/arecord ]; then arecord -q -D hw:1,0 | aplay -q - & fi if [ -f /usr/bin/tvtime ]; then tvtime -m --mixer=/dev/mixer:pcm fi pid=`pidof arecord` if [ $pid ]; then kill -9 $pid fi то hikkikamori@debian:~$ cat /media/local_disk1/.install/Скрипты/tv-tuner/tvtime.sh #!/bin/sh if [ -f /usr/bin/arecord ]; then arecord -q -D hw:1,0 | aplay -q - & fi if [ -f /usr/bin/tvtime ]; then tvtime -m --mixer=/dev/mixer:pcm fi pid=`pidof arecord` if [ $pid ]; then kill -9 $pid fi Код: hikkikamori@debian:~$ /media/local_disk1/.install/Скрипты/tv-tuner/tvtime.sh Запуск tvtime 1.0.2. Чтение конфигурации из /etc/tvtime/tvtime.xml Чтение конфигурации из /home/hikkikamori/.tvtime/tvtime.xml arecord: main:654: audio open error: Нет такого файла или каталога aplay: playback:2372: read error Спасибо за использование tvtime. звука нет, громкость не регулируется
|
|
|
hikkikamori
|
Добавлено: 05 ноя 2011, 02:13. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 02 ноя 2011, 00:23 Сообщения: 8
|
с этим скриптом Код: hikkikamori@debian:~$ cat ./tv-time.sh #!/bin/sh sox -q -c 2 -s -r 32000 -t ossdsp /dev/dsp2 -t ossdsp -r 32000 /dev/dsp & soxpid=$! sleep 0.5 tvtime kill $soxpid звук появился ![Озадачен :hm:](./images/smilies/icon_hm.gif)
|
|
|
hikkikamori
|
Добавлено: 07 ноя 2011, 19:58. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 02 ноя 2011, 00:23 Сообщения: 8
|
А когда будет осуществлена нормальная поддержка звука в Beholder TV H7 через PCI используя alsa?
|
|
|
Linux
|
Добавлено: 08 ноя 2011, 10:40. Заголовок сообщения: |
Re: Тюнер H7 |
|
Beholder | ![Аватара пользователя](./download/file.php?avatar=10588.jpg) |
Зарегистрирован: 19 авг 2004, 11:51 Сообщения: 396
|
H7 нормально отдает звук по PCI проблема в tvtime который не может его забрать и которому нужны всякие костыли.
|
|
|
hikkikamori
|
Добавлено: 08 ноя 2011, 20:50. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 02 ноя 2011, 00:23 Сообщения: 8
|
попробовал mplayer-ом Код: mplayer tv:// -tv driver=v4l2:normid=13:device=/dev/video0:alsa=1:adevice=hw.2,0:amode=0:audiorate=32000:forceaudio=1:immediatemode=0 звук есть А что за ошибка постоянно выходит при загрузке системы: Код: hikkikamori@debian:~$ dmesg |grep failed [ 31.489150] xc5000: I2C write failed (len=4) [ 31.489183] saa7133[0]/dvb: frontend initialization failed [ 140.405154] xc5000: I2C write failed (len=4) [ 140.405179] xc5000: I2C read failed Как вылечить?
|
|
|
sandy
|
Добавлено: 19 июл 2012, 02:50. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 19 июл 2012, 02:06 Сообщения: 3
|
Господа ! Помогите , перечитал тут все, но не могу настроить звук в дистрибутиве ALT Linux 6.0.2 KDesktop VLC тьюнер захватывает, если предварительно настроить канал TVtime, как hw:1,0 в TVtime звук не работает, xavtv - аналогично, скрипты не пойдут т.к. arecord у ALT нет FM - приемник не работает, /dev/mixer , /dev/pcm - нет в системе, звук премлим только по PCI (плата GA-525TUD - нет у нее aux)
выбор был обусловлен хорошими отзывами в интернете, и малыми размерами тьюнера (корпус MiniITX - Foxconn 338)
С уважением Александр - admin#yarpolinet.ru, icq - 578654865
|
|
|
EvilGremlin
|
Добавлено: 19 авг 2012, 21:25. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 19 авг 2012, 21:14 Сообщения: 3
|
Тоже прикупил пару Р7, тоже воюю со звуком. Пока не получается добиться звука от mplayer: Код: eg@eg-mint ~ $ mplayer tv:// -tv driver=v4l2:normid=8:device=/dev/video0:alsa:adevice=hw.0,0:audiorate=32000:forceaudio=1:immediatemode=0 MPlayer2 UNKNOWN (C) 2000-2011 MPlayer Team mplayer: could not connect to socket mplayer: No such file or directory Failed to open LIRC support. You will not be able to use your remote control.
Playing tv://. Detected file format: TV Selected driver: v4l2 name: Video 4 Linux 2 input author: Martin Olschewski <olschewski@zpr.uni-koeln.de> comment: first try, more to come ;-) Selected device: Beholder BeholdTV H7 Tuner cap: STEREO LANG1 LANG2 Tuner rxs: MONO Capabilities: video capture video overlay VBI capture device tuner read/write streaming supported norms: 0 = NTSC; 1 = NTSC-M; 2 = NTSC-M-JP; 3 = NTSC-M-KR; 4 = PAL; 5 = PAL-BG; 6 = PAL-H; 7 = PAL-I; 8 = PAL-DK; 9 = PAL-M; 10 = PAL-N; 11 = PAL-Nc; 12 = PAL-60; 13 = SECAM; 14 = SECAM-B; 15 = SECAM-G; 16 = SECAM-H; 17 = SECAM-DK; 18 = SECAM-L; 19 = SECAM-Lc; inputs: 0 = Television; 1 = Composite1; 2 = S-Video; Current input: 0 Current format: BGR24 v4l2: current audio mode is : MONO Channel count not available - reverting to default: 2 Channel count not available - reverting to default: 2 ========================================================================== Opening video decoder: [raw] RAW Uncompressed Video Movie-Aspect is undefined - no prescaling applied. VO: [vdpau] 640x480 => 640x480 Planar YV12 [vdpau] Got display refresh rate 59.887 Hz. [vdpau] If that value looks wrong give the -vo vdpau:fps=X suboption manually. Selected video codec: [rawyv12] vfm: raw (RAW YV12) ========================================================================== ========================================================================== Opening audio decoder: [pcm] Uncompressed PCM audio decoder AUDIO: 44100 Hz, 2 ch, s16le, 1411.2 kbit/100.00% (ratio: 176400->176400) Selected audio codec: [pcm] afm: pcm (Uncompressed PCM) ========================================================================== [AO OSS] audio_setup: Can't open audio device /dev/dsp: No such file or directory AO: [alsa] 48000Hz 2ch s16le (2 bytes per sample) Starting playback... A: 6.5 V: 6.5 A-V: -0.000 ct: 0.000 163/163 0% 5% 0.8% 0 0 v4l2: 170 frames successfully processed, 0 frames dropped.
Exiting... (Quit)
При этом если сделать loopback звук есть: Код: pactl load-module module-loopback source=alsa_input.pci-0000_07_00.0.analog-stereo Но эта затычка совершенно не устраивает, так как надо одновременно писать с 3-4 тюнеров, от бехолдеров нужно только радио. А VLC играет с такими параметрами: Код: :v4l2-standard=PAL_DK :input-slave=alsa://hw:1,0 :v4l2-input=0 :v4l2-audio-input=-1 :v4l2-tuner=0 :v4l2-tuner-frequency=-1 :v4l2-tuner-audio-mode=1 :live-caching=300 Мамка Intel DP35DP, Linux Mint 13, ядро 3.2.0-29-generic
|
|
|
sandy
|
Добавлено: 20 авг 2012, 06:11. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 19 июл 2012, 02:06 Сообщения: 3
|
на почту отпиши я в проблеме немного разобрался телевидение смотрю, правда по PCI так и не удалось, вывел шнурок на линейный вход mencoder - захватывает, tvtime - все работает, mplayer - то же осталось победить FM радио
при alsa=1 - звук идет как по PCI так и на разъем не забудь hw:1,0 - а не 0,0 0,0 - это у тебя встроенная звуковуха
|
|
|
sandy
|
Добавлено: 20 авг 2012, 06:27. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 19 июл 2012, 02:06 Сообщения: 3
|
не жму
mplayer tv:// -tv driver=v4l2:normid=17:fps=25:outfmt=i420:width=720:height=576:alsa:adevice=hw.1,0:amode=1:audiorate=32000:forceaudio:immediatemode=0
и немного со сжатием
mencoder tv:// -tv driver=v4l2:freq=663.25:normid=17:fps=25:outfmt=i420:width=720:height=540:alsa:adevice=hw.1,0:amode=1:audiorate=32000:forceaudio:immediatemode=0 -oac mp3lame -lameopts cbr:br=128 -ovc lavc -lavcopts vcodec=mpeg4:vbitrate=1500 -o tv.avi
пробовал xvid на лету - машина слабовата, выдерживает минуту, потом начинает терять кадры подкрути сам по вкусу
|
|
|
EvilGremlin
|
Добавлено: 20 авг 2012, 16:30. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 19 авг 2012, 21:14 Сообщения: 3
|
не, у меня типа всё правильно записано было, просто оно в lspci не светится почему-то никак, а vlc и alsamixer видят правильно, видимо это и есть основное отличие бехолдера от авера в линях. вот так с одним бехолдером выводит: Код: eg@eg-mint ~ $ lspci 00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 02) 00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 02) 00:03.0 Communication controller: Intel Corporation 82G33/G31/P35/P31 Express MEI Controller (rev 02) 00:19.0 Ethernet controller: Intel Corporation 82566DC-2 Gigabit Network Connection (rev 02) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 02) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 01:00.0 VGA compatible controller: NVIDIA Corporation G86 [GeForce 8500 GT] (rev a1) 03:00.0 IDE interface: Marvell Technology Group Ltd. 88SE6101/6102 single-port PATA133 interface (rev b1) 07:00.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1) 07:03.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22A IEEE-1394a-2000 Controller (PHY/Link) [iOHCI-Lynx]
уже разобрался, помогло так: Код: eg@eg-mint ~ $ cat /etc/modprobe.d/saa7134.conf options saa7134 secam=DK alsa=1 options saa7134_alsa index=2,3 enable=2,3 options xc5000 no_poweroff=1
по умолчанию оно то ли непонятно по какому адресу висело, то ли отключено было, надо принудительно задавать и включать, теперь они у меня hw:2.0 и hw:3.0 на первом у меня щас авер висит. теперь тв так кажет: Код: mplayer tv:// -tv driver=v4l2:freq=527.25:normid=8:device=/dev/video0:alsa:adevice=hw.2,0:audiorate=44100:amode=0:forceaudio:immediatemode=0 -vo vdpau -ao alsa а радио пишу так: Код: radio -c /dev/radio0 -f 83,3 -q arecord -D hw:2,0 -r 32000 -t wav -d 3600 | oggenc -q 5 - -o testout.ogg radio -c /dev/radio0 -m -q
|
|
|
EvilGremlin
|
Добавлено: 20 авг 2012, 17:32. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 19 авг 2012, 21:14 Сообщения: 3
|
теперь у меня другая проблема, при записи менкодером дикий прогрессирующий рассинхрон на любых кодеках, даже с пропуском кадров. на бехолдах мне видео нафиг не нужно, но факультативно проблему хотелось бы победить (мало ли что)
|
|
|
422digital
|
Добавлено: 06 апр 2013, 08:26. Заголовок сообщения: |
Re: Тюнер H7 |
|
Зарегистрирован: 12 июл 2009, 16:32 Сообщения: 31
|
Купил H7, ревизия d1, выпущен 01-2013, в системе ядро 2.6.32-5-686. В dmesg тюнер опознается как card=0, дальше идет строка: Код: saa7134: card=178 -> Beholder BeholdTV H7 5ace:7190 но в то же время lspci выдает: Код: Subsystem: Beholder International Ltd. Device 7191. Собирал 2 ядра: 3.0.71-686 и 3.8.5-686, тюнер не опознается. При ручном указании saa7134 card=178 тюнер опознается: Код: saa7133[0]: subsystem: 5ace:7191, board: Beholder BeholdTV H7 [card=178,insmod option] но на экране нет картинки, экран черный. Если заменить H7 на X7, все работает, картинка есть. Как быть с H7 относить в магазин ?
|
|
|
Кто сейчас на конференции |
Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 124 |
Вы не можете начинать темы Вы не можете отвечать на сообщения Вы не можете редактировать свои сообщения Вы не можете удалять свои сообщения Вы не можете добавлять вложения
|
|