[    0.758397] uhci_hcd: USB Universal Host Controller Interface driver
[    0.758450] xhci_hcd 0000:04:00.0: xHCI Host Controller
[    0.758453] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3
[    0.758591] xhci_hcd 0000:04:00.0: irq 40 for MSI/MSI-X
[    0.758657] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    0.758658] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.758659] usb usb3: Product: xHCI Host Controller
[    0.758661] usb usb3: Manufacturer: Linux 3.13.0-37-generic xhci_hcd
[    0.758662] usb usb3: SerialNumber: 0000:04:00.0
[    0.758727] hub 3-0:1.0: USB hub found
[    0.758734] hub 3-0:1.0: 2 ports detected
[    0.758782] xhci_hcd 0000:04:00.0: xHCI Host Controller
[    0.758784] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 4
[    0.758812] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    0.758814] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.758815] usb usb4: Product: xHCI Host Controller
[    0.758816] usb usb4: Manufacturer: Linux 3.13.0-37-generic xhci_hcd
[    0.758817] usb usb4: SerialNumber: 0000:04:00.0
[    0.758880] hub 4-0:1.0: USB hub found
[    0.758887] hub 4-0:1.0: 2 ports detected
[    0.766280] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    0.766694] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.766699] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.766934] mousedev: PS/2 mouse device common for all mice
[    0.767329] rtc_cmos 00:03: RTC can wake from S4
[    0.767545] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.767572] rtc_cmos 00:03: alarms up to one month, 242 bytes nvram, hpet irqs
[    0.767618] device-mapper: uevent: version 1.0.3
[    0.767674] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[    0.767679] ledtrig-cpu: registered to indicate activity on CPUs
[    0.767748] TCP: cubic registered
[    0.767805] NET: Registered protocol family 10
[    0.767925] NET: Registered protocol family 17
[    0.767931] Key type dns_resolver registered
[    0.768238] Loading compiled-in X.509 certificates
[    0.768947] Loaded X.509 cert 'Magrathea: Glacier signing key: 2cb1133b35f95a9e24deabeeb12ba449bcbabbc9'
[    0.768960] registered taskstats version 1
[    0.770540] Key type trusted registered
[    0.771768] Key type encrypted registered
[    0.772980] AppArmor: AppArmor sha1 policy hashing enabled
[    0.772983] IMA: No TPM chip found, activating TPM-bypass!
[    0.773213] regulator-dummy: disabling
[    0.773254]   Magic number: 7:677:288
[    0.773279] tty tty21: hash matches
[    0.773345] rtc_cmos 00:03: setting system clock to 2015-07-02 17:16:33 UTC (1435857393)
[    0.773816] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.773818] EDD information not available.
[    0.773836] PM: Hibernation image not present or could not be loaded.
[    0.789263] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[    1.054142] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    1.186501] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[    1.186506] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.186796] hub 1-1:1.0: USB hub found
[    1.186874] hub 1-1:1.0: 4 ports detected
[    1.202133] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.202236] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.210309] ata3.00: ATAPI: ASUS    DRW-24B5ST, 1.00, max UDMA/100
[    1.210370] ata4.00: ATAPI: ASUS    DRW-24B3ST, 1.00, max UDMA/100
[    1.226297] ata4.00: configured for UDMA/100
[    1.226347] ata3.00: configured for UDMA/100
[    1.298123] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    1.430446] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[    1.430450] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.430748] hub 2-1:1.0: USB hub found
[    1.430824] hub 2-1:1.0: 6 ports detected
[    1.522009] tsc: Refined TSC clocksource calibration: 3092.974 MHz
[    1.702141] usb 2-1.3: new high-speed USB device number 3 using ehci-pci
[    1.983206] usb 2-1.3: New USB device found, idVendor=048d, idProduct=1336
[    1.983211] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.983214] usb 2-1.3: Product: Mass Storage Device
[    1.983216] usb 2-1.3: Manufacturer: Generic   
[    1.983219] usb 2-1.3: SerialNumber: 00000000000006
[    2.073893] ata1.01: failed to resume link (SControl 0)
[    2.073978] ata2.01: failed to resume link (SControl 0)
[    2.084724] ata2.00: SATA link down (SStatus 0 SControl 300)
[    2.084736] ata2.01: SATA link down (SStatus 0 SControl 0)
[    2.229917] ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.229928] ata1.01: SATA link down (SStatus 0 SControl 0)
[    2.239012] ata1.00: ATA-8: WDC WD10EFRX-68JCSN0, 01.01A01, max UDMA/133
[    2.239017] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    2.247013] ata1.00: configured for UDMA/133
[    2.247218] scsi 0:0:0:0: Direct-Access     ATA      WDC WD10EFRX-68J 01.0 PQ: 0 ANSI: 5
[    2.247315] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    2.247318] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    2.247319] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.247426] sd 0:0:0:0: [sda] Write Protect is off
[    2.247430] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.247470] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.250641] scsi 2:0:0:0: CD-ROM            ASUS     DRW-24B5ST       1.00 PQ: 0 ANSI: 5
[    2.254268] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.254270] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.254336] sr 2:0:0:0: Attached scsi CD-ROM sr0
[    2.254384] sr 2:0:0:0: Attached scsi generic sg1 type 5
[    2.257810] scsi 3:0:0:0: CD-ROM            ASUS     DRW-24B3ST       1.00 PQ: 0 ANSI: 5
[    2.261221] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.261383] sr 3:0:0:0: Attached scsi CD-ROM sr1
[    2.261433] sr 3:0:0:0: Attached scsi generic sg2 type 5
[    2.277539]  sda: sda1 sda2 sda3
[    2.278213] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.279272] Freeing unused kernel memory: 1336K (ffffffff81d20000 - ffffffff81e6e000)
[    2.279275] Write protecting the kernel read-only data: 12288k
[    2.280880] Freeing unused kernel memory: 804K (ffff880001737000 - ffff880001800000)
[    2.282194] Freeing unused kernel memory: 692K (ffff880001b53000 - ffff880001c00000)
[    2.291499] systemd-udevd[135]: starting version 204
[    2.307611] [drm] Initialized drm 1.1.0 20060810
[    2.312420] usb-storage 2-1.3:1.0: USB Mass Storage device detected
[    2.322648] scsi4 : usb-storage 2-1.3:1.0
[    2.322720] usbcore: registered new interface driver usb-storage
[    2.322936] [drm] Memory usable by graphics device = 2048M
[    2.339176] atl1c 0000:05:00.0: version 1.0.1.1-NAPI
[    2.361844] i915 0000:00:02.0: irq 41 for MSI/MSI-X
[    2.361855] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    2.361857] [drm] Driver supports precise vblank timestamp query.
[    2.361913] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    2.379656] [drm] Wrong MCH_SSKPD value: 0x16040307
[    2.379658] [drm] This can cause pipe underruns and display issues.
[    2.379660] [drm] Please upgrade your BIOS to fix this.
[    2.408205] fbcon: inteldrmfb (fb0) is primary device
[    2.521959] Switched to clocksource tsc
[    2.592270] Console: switching to colour frame buffer device 160x64
[    2.594654] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[    2.594655] i915 0000:00:02.0: registered panic notifier
[    2.594686] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    2.718693] psmouse serio1: alps: Unknown ALPS touchpad: E7=10 00 64, EC=10 00 64
[    3.061233] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[    3.322453] scsi 4:0:0:0: Direct-Access     Generic  Storage Device   0.00 PQ: 0 ANSI: 2
[    3.322610] sd 4:0:0:0: Attached scsi generic sg3 type 0
[    3.323988] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[    3.482890] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[    3.731564] random: nonblocking pool is initialized
[    3.813509] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[   16.081892] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.142581] systemd-udevd[379]: starting version 204
[   16.310896] EXT4-fs (sda3): re-mounted. Opts: errors=remount-ro
[   16.316815] lp: driver loaded but no devices found
[   16.323383] ppdev: user-space parallel port driver
[   16.327208] parport_pc 00:07: reported by Plug and Play ACPI
[   16.327259] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   16.356212] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \GP2C 1 (20131115/utaddress-251)
[   16.356220] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   16.356242] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   16.359538] media: module verification failed: signature and/or  required key missing - tainting kernel
[   16.360853] media: Linux media interface: v0.10
[   16.363691] Linux video capture interface: v2.00
[   16.363695] WARNING: You are using an experimental version of the media stack.
[   16.363695] 	As the driver is backported to an older kernel, it doesn't offer
[   16.363695] 	enough quality for its usage in production.
[   16.363695] 	Use it with care.
[   16.363695] Latest git patches (needed if you report a bug to linux-media@vger.kernel.org):
[   16.363695] 	135f9be9194cf7778eb73594aa55791b229cf27c [media] dvb_frontend: start media pipeline while thread is running
[   16.363695] 	0f0fa90bd035fa15106799b813d4f0315d99f47e [media] cx231xx: enable tuner->decoder link at videobuf start
[   16.363695] 	9239effd53d47e3cd9c653830c8465c0a3a427dc [media] dvb-frontend: enable tuner link when the FE thread starts
[   16.365215] WARNING: You are using an experimental version of the media stack.
[   16.365215] 	As the driver is backported to an older kernel, it doesn't offer
[   16.365215] 	enough quality for its usage in production.
[   16.365215] 	Use it with care.
[   16.365215] Latest git patches (needed if you report a bug to linux-media@vger.kernel.org):
[   16.365215] 	135f9be9194cf7778eb73594aa55791b229cf27c [media] dvb_frontend: start media pipeline while thread is running
[   16.365215] 	0f0fa90bd035fa15106799b813d4f0315d99f47e [media] cx231xx: enable tuner->decoder link at videobuf start
[   16.365215] 	9239effd53d47e3cd9c653830c8465c0a3a427dc [media] dvb-frontend: enable tuner link when the FE thread starts
[   16.366174] mei_me 0000:00:16.0: irq 42 for MSI/MSI-X
[   16.381477] saa7130/34: v4l2 driver version 0, 2, 17 loaded
[   16.381691] saa7133[0]: found at 0000:03:00.0, rev: 209, irq: 17, latency: 32, mmio: 0xfbdff000
[   16.381700] saa7133[0]: subsystem: 5ace:7290, board: Beholder BeholdTV T7 [card=194,autodetected]
[   16.381715] saa7133[0]: board init: gpio is 0
[   16.424517] lp0: using parport0 (interrupt-driven).
[   16.458747] device-mapper: multipath: version 1.6.0 loaded
[   16.496349] snd_hda_intel 0000:00:1b.0: irq 43 for MSI/MSI-X
[   16.506700] saa7133[0]: i2c eeprom 00: ce 5a 90 72 54 20 00 00 00 00 00 00 00 00 00 01
[   16.506710] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506717] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506724] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506730] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506737] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506744] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506751] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506758] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506765] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506771] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506778] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506784] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506791] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506798] saa7133[0]: i2c eeprom e0: a7 1f 01 00 ff ff ff ff ff ff ff ff ff ff ff ff
[   16.506804] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff
[   16.509323] SKU: Nid=0x1d sku_cfg=0x4005e601
[   16.509326] SKU: port_connectivity=0x1
[   16.509327] SKU: enable_pcbeep=0x0
[   16.509328] SKU: check_sum=0x00000005
[   16.509329] SKU: customization=0x000000e6
[   16.509330] SKU: external_amp=0x0
[   16.509332] SKU: platform_type=0x0
[   16.509333] SKU: swap=0x0
[   16.509334] SKU: override=0x1
[   16.510553] autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[   16.510557]    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   16.510559]    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   16.510560]    mono: mono_out=0x0
[   16.510561]    inputs:
[   16.510563]      Rear Mic=0x18
[   16.510564]      Front Mic=0x19
[   16.510566]      Line=0x1a
[   16.510568]      CD=0x1c
[   16.510569] realtek: No valid SSID, checking pincfg 0x4005e601 for NID 0x1d
[   16.510571] realtek: Enabling init ASM_ID=0xe601 CODEC_ID=10ec0889
[   16.518737] tuner 9-0061: Tuner -1 found with type(s) Radio TV.
[   16.522196] xc5000: xc5000_attach(9-0061)
[   16.522199] xc5000 9-0061: creating new instance
[   16.527193] xc5000: XREG_PRODUCT_ID 2000
[   16.527197] xc5000: Successfully identified at address 0x61
[   16.527198] xc5000: Firmware has not been loaded previously
[   16.527205] xc5000: xc5000_config_tv() frequency=6400 (in units of 62.5khz)
[   16.534300] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   16.537207] xc5000: xc5000_is_firmware_loaded() returns True id = 0x20
[   16.537211] xc5000: xc_set_signal_source(1) Source = CABLE
[   16.538649] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[   16.540398] input: HDA Intel PCH Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[   16.540468] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[   16.540527] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[   16.540582] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[   16.550724] xc5000: xc_set_tv_standard(0x8049,0x0c04)
[   16.550727] xc5000: xc_set_tv_standard() Standard = B/G-PAL-NICAM
[   16.565024] gpio_ich: GPIO from 180 to 255 on gpio_ich
[   16.598674] xc5000: xc_tune_channel(400000000)
[   16.598678] xc5000: xc_set_rf_frequency(400000000)
[   16.746644] xc5000: *** ADC envelope (0-1023) = 1540
[   16.754641] xc5000: *** Frequency error = 0 Hz
[   16.762635] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 2814
[   16.778662] xc5000: *** HW: V0.0, FW: V 0.0.0
[   16.786646] xc5000: *** Horizontal sync frequency = 7355 Hz
[   16.794628] xc5000: *** Frame lines = 980
[   16.802643] xc5000: *** Quality (0:<8dB, 7:>56dB) = 0
[   16.810659] xc5000: *** Unweighted analog SNR = 58 dB
[   16.818638] xc5000: *** Total gain = 211.80 dB
[   16.818649] xc5000: xc5000_config_tv() frequency=6400 (in units of 62.5khz)
[   16.826637] xc5000: xc5000_is_firmware_loaded() returns False id = 0x2000
[   17.117718] xc5000: firmware read 16497 bytes.
[   17.117721] xc5000: waiting for firmware upload (dvb-fe-xc5000c-4.1.30.7.fw)...
[   17.117722] xc5000: firmware uploading...
[   17.117723] xc5000: xc5000_tuner_reset()
[   17.260650] init: failsafe main process (706) killed by TERM signal
[   17.694805] Bluetooth: Core ver 2.17
[   17.694826] NET: Registered protocol family 31
[   17.694828] Bluetooth: HCI device and connection manager initialized
[   17.694872] Bluetooth: HCI socket layer initialized
[   17.694875] Bluetooth: L2CAP socket layer initialized
[   17.694880] Bluetooth: SCO socket layer initialized
[   17.697180] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   17.697183] Bluetooth: BNEP filters: protocol multicast
[   17.697189] Bluetooth: BNEP socket layer initialized
[   17.698301] Bluetooth: RFCOMM TTY layer initialized
[   17.698311] Bluetooth: RFCOMM socket layer initialized
[   17.698315] Bluetooth: RFCOMM ver 1.11
[   18.113696] init: cups main process (783) killed by HUP signal
[   18.113705] init: cups main process ended, respawning
[   19.402055] xc5000: Firmware upload complete...
[   19.434051] xc5000: xc_initialize()
[   19.623834] atl1c 0000:05:00.0: irq 44 for MSI/MSI-X
[   19.624386] atl1c 0000:05:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
[   19.766018] xc5000: Firmware dvb-fe-xc5000c-4.1.30.7.fw loaded and running.
[   19.766024] xc5000: xc_set_signal_source(1) Source = CABLE
[   19.781997] xc5000: xc_set_tv_standard(0x8049,0x0c04)
[   19.782003] xc5000: xc_set_tv_standard() Standard = B/G-PAL-NICAM
[   19.829981] xc5000: xc_tune_channel(400000000)
[   19.829986] xc5000: xc_set_rf_frequency(400000000)
[   19.835836] init: samba-ad-dc main process (814) terminated with status 1
[   20.557804] xc5000: *** ADC envelope (0-1023) = 376
[   20.565794] xc5000: *** Frequency error = 406 Hz
[   20.573788] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 2
[   20.589833] xc5000: *** HW: V6.0, FW: V 4.1.57374
[   20.597794] xc5000: *** Horizontal sync frequency = 15496 Hz
[   20.605792] xc5000: *** Frame lines = 802
[   20.613785] xc5000: *** Quality (0:<8dB, 7:>56dB) = 5
[   20.621803] xc5000: *** Unweighted analog SNR = 63 dB
[   20.629792] xc5000: *** Total gain = 124.18 dB
[   20.637791] xc5000: *** PLL lock status = 0x0000
[   20.693767] Registered IR keymap rc-behold
[   20.693858] input: i2c IR (BeholdTV) as /devices/virtual/rc/rc0/input11
[   20.693923] rc0: i2c IR (BeholdTV) as /devices/virtual/rc/rc0
[   20.693925] ir-kbd-i2c: i2c IR (BeholdTV) detected at i2c-9/9-002d/ir0 [saa7133[0]]
[   20.694145] xc5000: xc5000_sleep()
[   20.694185] saa7133[0]: registered device video0 [v4l2]
[   20.694214] saa7133[0]: registered device vbi0
[   20.694240] saa7133[0]: registered device radio0
[   20.695857] saa7134 ALSA driver for DMA sound loaded
[   20.695885] saa7133[0]/alsa: saa7133[0] at 0xfbdff000 irq 17 registered as card -2
[   20.697913] WARNING: You are using an experimental version of the media stack.
[   20.697913] 	As the driver is backported to an older kernel, it doesn't offer
[   20.697913] 	enough quality for its usage in production.
[   20.697913] 	Use it with care.
[   20.697913] Latest git patches (needed if you report a bug to linux-media@vger.kernel.org):
[   20.697913] 	135f9be9194cf7778eb73594aa55791b229cf27c [media] dvb_frontend: start media pipeline while thread is running
[   20.697913] 	0f0fa90bd035fa15106799b813d4f0315d99f47e [media] cx231xx: enable tuner->decoder link at videobuf start
[   20.697913] 	9239effd53d47e3cd9c653830c8465c0a3a427dc [media] dvb-frontend: enable tuner link when the FE thread starts
[   20.698487] dvb_init() allocating 1 frontend
[   20.699264] xc5000: xc5000_config_tv() frequency=6400 (in units of 62.5khz)
[   20.703917] i2c i2c-9: Added multiplexed i2c bus 10
[   20.703922] si2168 9-0064: Silicon Labs Si2168 successfully attached
[   20.703934] xc5000: xc5000_attach(9-0061)
[   20.703936] xc5000 9-0061: attaching existing instance
[   20.705777] xc5000: xc5000_is_firmware_loaded() returns True id = 0x14b4
[   20.705780] xc5000: xc_set_signal_source(1) Source = CABLE
[   20.713765] xc5000: XREG_PRODUCT_ID 14b4
[   20.713767] xc5000: Successfully identified at address 0x61
[   20.713768] xc5000: Firmware has been loaded previously
[   20.713770] DVB: registering new adapter (saa7133[0])
[   20.713774] saa7134 0000:03:00.0: DVB: registering adapter 0 frontend 0 (Silicon Labs Si2168)...
[   20.737797] xc5000: xc_set_tv_standard(0x8049,0x0c04)
[   20.737804] xc5000: xc_set_tv_standard() Standard = B/G-PAL-NICAM
[   20.809761] si2168 9-0064: found a 'Silicon Labs Si2168-A30 build 2 id 0'
[   20.824702] si2168 9-0064: downloading firmware from file 'dvb-demod-si2168-a30b2-01.fw'
[   20.825769] xc5000: xc_tune_channel(400000000)
[   20.825779] xc5000: xc_set_rf_frequency(400000000)
[   21.573585] xc5000: *** ADC envelope (0-1023) = 356
[   21.589578] xc5000: *** Frequency error = 78 Hz
[   21.605573] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 2
[   21.637599] xc5000: *** HW: V6.0, FW: V 4.1.57374
[   21.653561] xc5000: *** Horizontal sync frequency = 15542 Hz
[   21.669559] xc5000: *** Frame lines = 65535
[   21.685562] xc5000: *** Quality (0:<8dB, 7:>56dB) = 5
[   21.701558] xc5000: *** Unweighted analog SNR = 63 dB
[   21.717541] xc5000: *** Total gain = 124.18 dB
[   21.733534] xc5000: *** PLL lock status = 0x0001
[   21.773648] xc5000: xc5000_config_radio() frequency=1400000 (in units of khz)
[   21.789526] xc5000: xc5000_is_firmware_loaded() returns True id = 0x14b4
[   21.789530] xc5000: xc_set_tv_standard(0x9002,0x0208)
[   21.789532] xc5000: xc_set_tv_standard() Standard = FM Radio-INPUT1
[   21.853540] xc5000: xc_set_signal_source(0) Source = ANTENNA
[   21.917540] xc5000: xc_tune_channel(87500000)
[   21.917546] xc5000: xc_set_rf_frequency(87500000)
[   22.205271] vboxdrv: Found 4 processor cores.
[   22.205835] vboxdrv: fAsync=0 offMin=0x352 offMax=0x1a96
[   22.205910] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   22.205912] vboxdrv: Successfully loaded version 4.3.26 (interface 0x001a000a).
[   22.229460] xc5000: xc5000_config_tv() frequency=6400 (in units of 62.5khz)
[   22.245452] xc5000: xc5000_is_firmware_loaded() returns True id = 0x14b4
[   22.245458] xc5000: xc_set_signal_source(1) Source = CABLE
[   22.281433] xc5000: xc_set_tv_standard(0x8049,0x0c04)
[   22.281437] xc5000: xc_set_tv_standard() Standard = B/G-PAL-NICAM
[   22.377468] xc5000: xc_tune_channel(400000000)
[   22.377471] xc5000: xc_set_rf_frequency(400000000)
[   22.415906] vboxpci: IOMMU not found (not registered)
[   22.488650] init: plymouth-upstart-bridge main process ended, respawning
[   22.495444] init: plymouth-upstart-bridge main process (1609) terminated with status 1
[   22.495456] init: plymouth-upstart-bridge main process ended, respawning
[   22.783322] init: plymouth-stop pre-start process (1668) terminated with status 1
[   23.109256] xc5000: *** ADC envelope (0-1023) = 648
[   23.125239] xc5000: *** Frequency error = 421 Hz
[   23.141232] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 2
[   23.173317] xc5000: *** HW: V6.0, FW: V 4.1.57374
[   23.189258] xc5000: *** Horizontal sync frequency = 15450 Hz
[   23.205238] xc5000: *** Frame lines = 65535
[   23.221230] xc5000: *** Quality (0:<8dB, 7:>56dB) = 0
[   23.237285] xc5000: *** Unweighted analog SNR = 0 dB
[   23.253244] xc5000: *** Total gain = 124.18 dB
[   23.269220] xc5000: *** PLL lock status = 0x0001
[   23.301393] xc5000: xc5000_sleep()
[   23.301410] xc5000: xc5000_sleep()
[   23.301536] xc5000: xc5000_sleep()
[   61.199850] si2168 9-0064: wait 59 
[   62.204149] si2168 9-0064: wait 58 
[   63.208468] si2168 9-0064: wait 57 
[   64.212728] si2168 9-0064: wait 56 
[   65.217041] si2168 9-0064: wait 55 
[   66.221341] si2168 9-0064: wait 54 
[   67.225663] si2168 9-0064: wait 53 
[   68.229938] si2168 9-0064: wait 52 
[   69.234248] si2168 9-0064: wait 51 
[   70.238531] si2168 9-0064: wait 50 
[   71.242858] si2168 9-0064: wait 49 
[   72.247132] si2168 9-0064: wait 48 
[   72.495230] si2168 9-0064: firmware download took 51664 ms
[   72.527209] si2168 9-0064: firmware version: 3.0.20
[   72.599259] xc5000: xc5000_sleep()
[   73.251447] si2168 9-0064: wait 47 
[   73.299453] xc5000: xc5000_init()
[   73.307441] xc5000: xc5000_is_firmware_loaded() returns True id = 0x14b4
[   73.419501] xc5000: *** ADC envelope (0-1023) = 412
[   73.427475] xc5000: *** Frequency error = 78 Hz
[   73.435508] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 2
[   73.451492] xc5000: *** HW: V6.0, FW: V 4.1.57374
[   73.459497] xc5000: *** Horizontal sync frequency = 15900 Hz
[   73.467486] xc5000: *** Frame lines = 65535
[   73.475489] xc5000: *** Quality (0:<8dB, 7:>56dB) = 5
[   73.483522] xc5000: *** Unweighted analog SNR = 63 dB
[   73.491495] xc5000: *** Total gain = 124.18 dB
[   73.499496] xc5000: *** PLL lock status = 0x0001
[   73.507529] xc5000: xc5000_is_firmware_loaded() returns True id = 0x14b4
[   73.507534] xc5000: xc5000_set_digital_params() frequency=554000000 (Hz)
[   73.507536] xc5000: xc5000_set_digital_params() OFDM
[   73.507538] xc5000: xc5000_set_digital_params() frequency=554000000 (compensated to 551250000)
[   73.507540] xc5000: xc_set_signal_source(0) Source = ANTENNA
[   73.523533] xc5000: xc_set_tv_standard(0x800b,0x00c0)
[   73.523537] xc5000: xc_set_tv_standard() Standard = DTV8
[   73.555528] xc5000: xc_set_IF_frequency(freq_khz = 5000) freq_code = 0x1400
[   73.571548] xc5000: xc5000_tune_digital() setting OUTPUT_AMP to 0x8a
[   73.587523] xc5000: xc_tune_channel(551250000)
[   73.587527] xc5000: xc_set_rf_frequency(551250000)
[   74.215735] xc5000: *** ADC envelope (0-1023) = 688
[   74.223713] xc5000: *** Frequency error = 0 Hz
[   74.231715] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 1
[   74.247753] xc5000: *** HW: V6.0, FW: V 4.1.57374
[   74.255708] xc5000: *** Horizontal sync frequency = 15778 Hz
[   74.263740] xc5000: *** Frame lines = 1435
[   74.271712] xc5000: *** Quality (0:<8dB, 7:>56dB) = 5
[   74.279714] xc5000: *** Unweighted analog SNR = 54 dB
[   74.287748] xc5000: *** Total gain = 88.78 dB
[   74.295719] xc5000: *** PLL lock status = 0x0001
[   76.316395] xc5000 9-0061: Total Gain: -88dB (22730)
[   78.052894] xc5000 9-0061: Total Gain: -88dB (22730)
[   79.917409] xc5000 9-0061: Total Gain: -88dB (22730)
[   81.769979] xc5000 9-0061: Total Gain: -88dB (22730)
[   83.678546] xc5000 9-0061: Total Gain: -88dB (22730)
[   85.595113] xc5000 9-0061: Total Gain: -88dB (22730)
[   87.435656] xc5000 9-0061: Total Gain: -88dB (22730)
[   89.344215] xc5000 9-0061: Total Gain: -88dB (22730)
[   91.316815] xc5000 9-0061: Total Gain: -88dB (22730)
[   93.233389] xc5000 9-0061: Total Gain: -88dB (22730)
[   95.133926] xc5000 9-0061: Total Gain: -88dB (22730)
[   96.998501] xc5000 9-0061: Total Gain: -88dB (22730)
[   98.891067] xc5000 9-0061: Total Gain: -88dB (22730)
[  100.795629] xc5000 9-0061: Total Gain: -88dB (22730)
[  102.732205] xc5000 9-0061: Total Gain: -88dB (22730)
[  104.612753] xc5000 9-0061: Total Gain: -88dB (22730)
[  106.513312] xc5000 9-0061: Total Gain: -88dB (22730)
[  108.393893] xc5000 9-0061: Total Gain: -88dB (22730)
[  110.302460] xc5000 9-0061: Total Gain: -88dB (22730)
[  112.151006] xc5000 9-0061: Total Gain: -88dB (22730)
[  114.051563] xc5000 9-0061: Total Gain: -88dB (22730)
[  115.928127] xc5000 9-0061: Total Gain: -88dB (22730)
[  117.828701] xc5000 9-0061: Total Gain: -88dB (22730)
[  119.725257] xc5000 9-0061: Total Gain: -88dB (22730)
[  121.593810] xc5000 9-0061: Total Gain: -88dB (22730)
user@Andrey-Linux ~ $ 
