r 3
[    0.758515] xhci_hcd 0000:04:00.0: irq 40 for MSI/MSI-X
[    0.758582] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    0.758584] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.758585] usb usb3: Product: xHCI Host Controller
[    0.758586] usb usb3: Manufacturer: Linux 3.13.0-37-generic xhci_hcd
[    0.758587] usb usb3: SerialNumber: 0000:04:00.0
[    0.758698] hub 3-0:1.0: USB hub found
[    0.758705] hub 3-0:1.0: 2 ports detected
[    0.758753] xhci_hcd 0000:04:00.0: xHCI Host Controller
[    0.758755] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 4
[    0.758783] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    0.758785] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.758786] usb usb4: Product: xHCI Host Controller
[    0.758787] usb usb4: Manufacturer: Linux 3.13.0-37-generic xhci_hcd
[    0.758788] usb usb4: SerialNumber: 0000:04:00.0
[    0.758869] hub 4-0:1.0: USB hub found
[    0.758877] hub 4-0:1.0: 2 ports detected
[    0.766175] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    0.766584] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.766589] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.766824] mousedev: PS/2 mouse device common for all mice
[    0.767167] rtc_cmos 00:03: RTC can wake from S4
[    0.767331] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.767357] rtc_cmos 00:03: alarms up to one month, 242 bytes nvram, hpet irqs
[    0.767404] device-mapper: uevent: version 1.0.3
[    0.767458] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[    0.767463] ledtrig-cpu: registered to indicate activity on CPUs
[    0.767532] TCP: cubic registered
[    0.767592] NET: Registered protocol family 10
[    0.767714] NET: Registered protocol family 17
[    0.767723] Key type dns_resolver registered
[    0.767966] Loading compiled-in X.509 certificates
[    0.768675] Loaded X.509 cert 'Magrathea: Glacier signing key: 2cb1133b35f95a9e24deabeeb12ba449bcbabbc9'
[    0.768684] registered taskstats version 1
[    0.770233] Key type trusted registered
[    0.771462] Key type encrypted registered
[    0.772650] AppArmor: AppArmor sha1 policy hashing enabled
[    0.772653] IMA: No TPM chip found, activating TPM-bypass!
[    0.772897] regulator-dummy: disabling
[    0.772937]   Magic number: 7:639:842
[    0.773027] rtc_cmos 00:03: setting system clock to 2015-07-02 16:48:18 UTC (1435855698)
[    0.773498] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.773499] EDD information not available.
[    0.773518] PM: Hibernation image not present or could not be loaded.
[    0.790946] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[    1.054049] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    1.186406] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[    1.186411] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.186700] hub 1-1:1.0: USB hub found
[    1.186779] hub 1-1:1.0: 4 ports detected
[    1.202044] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.202147] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.210215] ata4.00: ATAPI: ASUS    DRW-24B3ST, 1.00, max UDMA/100
[    1.210277] ata3.00: ATAPI: ASUS    DRW-24B5ST, 1.00, max UDMA/100
[    1.226211] ata4.00: configured for UDMA/100
[    1.226261] ata3.00: configured for UDMA/100
[    1.298039] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    1.430364] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[    1.430368] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.430648] hub 2-1:1.0: USB hub found
[    1.430725] hub 2-1:1.0: 6 ports detected
[    1.521926] tsc: Refined TSC clocksource calibration: 3092.974 MHz
[    1.702046] usb 2-1.3: new high-speed USB device number 3 using ehci-pci
[    1.983231] usb 2-1.3: New USB device found, idVendor=048d, idProduct=1336
[    1.983236] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.983239] usb 2-1.3: Product: Mass Storage Device
[    1.983242] usb 2-1.3: Manufacturer: Generic   
[    1.983244] usb 2-1.3: SerialNumber: 00000000000006
[    2.073810] ata1.01: failed to resume link (SControl 0)
[    2.073896] ata2.01: failed to resume link (SControl 0)
[    2.084630] ata2.00: SATA link down (SStatus 0 SControl 300)
[    2.084643] ata2.01: SATA link down (SStatus 0 SControl 0)
[    2.229837] ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.229848] ata1.01: SATA link down (SStatus 0 SControl 0)
[    2.238158] ata1.00: ATA-8: WDC WD10EFRX-68JCSN0, 01.01A01, max UDMA/133
[    2.238163] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    2.246168] ata1.00: configured for UDMA/133
[    2.246347] scsi 0:0:0:0: Direct-Access     ATA      WDC WD10EFRX-68J 01.0 PQ: 0 ANSI: 5
[    2.246446] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    2.246449] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    2.246450] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.246525] sd 0:0:0:0: [sda] Write Protect is off
[    2.246527] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.246556] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.249790] scsi 2:0:0:0: CD-ROM            ASUS     DRW-24B5ST       1.00 PQ: 0 ANSI: 5
[    2.253469] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.253473] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.253634] sr 2:0:0:0: Attached scsi CD-ROM sr0
[    2.253679] sr 2:0:0:0: Attached scsi generic sg1 type 5
[    2.257144] scsi 3:0:0:0: CD-ROM            ASUS     DRW-24B3ST       1.00 PQ: 0 ANSI: 5
[    2.260547] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.260733] sr 3:0:0:0: Attached scsi CD-ROM sr1
[    2.260783] sr 3:0:0:0: Attached scsi generic sg2 type 5
[    2.268134]  sda: sda1 sda2 sda3
[    2.268641] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.269703] Freeing unused kernel memory: 1336K (ffffffff81d20000 - ffffffff81e6e000)
[    2.269705] Write protecting the kernel read-only data: 12288k
[    2.271265] Freeing unused kernel memory: 804K (ffff880001737000 - ffff880001800000)
[    2.272559] Freeing unused kernel memory: 692K (ffff880001b53000 - ffff880001c00000)
[    2.281914] systemd-udevd[135]: starting version 204
[    2.295338] [drm] Initialized drm 1.1.0 20060810
[    2.306204] usb-storage 2-1.3:1.0: USB Mass Storage device detected
[    2.306925] scsi4 : usb-storage 2-1.3:1.0
[    2.306988] usbcore: registered new interface driver usb-storage
[    2.314437] [drm] Memory usable by graphics device = 2048M
[    2.335306] atl1c 0000:05:00.0: version 1.0.1.1-NAPI
[    2.353784] i915 0000:00:02.0: irq 41 for MSI/MSI-X
[    2.353793] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    2.353794] [drm] Driver supports precise vblank timestamp query.
[    2.353842] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    2.371352] [drm] Wrong MCH_SSKPD value: 0x16040307
[    2.371354] [drm] This can cause pipe underruns and display issues.
[    2.371355] [drm] Please upgrade your BIOS to fix this.
[    2.400280] fbcon: inteldrmfb (fb0) is primary device
[    2.521873] Switched to clocksource tsc
[    2.576095] Console: switching to colour frame buffer device 160x64
[    2.578479] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[    2.578481] i915 0000:00:02.0: registered panic notifier
[    2.578515] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    2.714217] psmouse serio1: alps: Unknown ALPS touchpad: E7=10 00 64, EC=10 00 64
[    3.029587] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[    3.306332] scsi 4:0:0:0: Direct-Access     Generic  Storage Device   0.00 PQ: 0 ANSI: 2
[    3.306566] sd 4:0:0:0: Attached scsi generic sg3 type 0
[    3.307926] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[    3.479274] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[    3.513627] random: nonblocking pool is initialized
[    3.813430] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[   15.987037] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.066548] systemd-udevd[379]: starting version 204
[   16.182274] lp: driver loaded but no devices found
[   16.184527] parport_pc 00:07: reported by Plug and Play ACPI
[   16.184597] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   16.193623] ppdev: user-space parallel port driver
[   16.196619] mei_me 0000:00:16.0: irq 42 for MSI/MSI-X
[   16.199789] media: module verification failed: signature and/or  required key missing - tainting kernel
[   16.200008] media: Linux media interface: v0.10
[   16.200916] Linux video capture interface: v2.00
[   16.200920] WARNING: You are using an experimental version of the media stack.
[   16.200920] 	As the driver is backported to an older kernel, it doesn't offer
[   16.200920] 	enough quality for its usage in production.
[   16.200920] 	Use it with care.
[   16.200920] Latest git patches (needed if you report a bug to linux-media@vger.kernel.org):
[   16.200920] 	135f9be9194cf7778eb73594aa55791b229cf27c [media] dvb_frontend: start media pipeline while thread is running
[   16.200920] 	0f0fa90bd035fa15106799b813d4f0315d99f47e [media] cx231xx: enable tuner->decoder link at videobuf start
[   16.200920] 	9239effd53d47e3cd9c653830c8465c0a3a427dc [media] dvb-frontend: enable tuner link when the FE thread starts
[   16.201932] WARNING: You are using an experimental version of the media stack.
[   16.201932] 	As the driver is backported to an older kernel, it doesn't offer
[   16.201932] 	enough quality for its usage in production.
[   16.201932] 	Use it with care.
[   16.201932] Latest git patches (needed if you report a bug to linux-media@vger.kernel.org):
[   16.201932] 	135f9be9194cf7778eb73594aa55791b229cf27c [media] dvb_frontend: start media pipeline while thread is running
[   16.201932] 	0f0fa90bd035fa15106799b813d4f0315d99f47e [media] cx231xx: enable tuner->decoder link at videobuf start
[   16.201932] 	9239effd53d47e3cd9c653830c8465c0a3a427dc [media] dvb-frontend: enable tuner link when the FE thread starts
[   16.207370] saa7130/34: v4l2 driver version 0, 2, 17 loaded
[   16.207577] saa7133[0]: found at 0000:03:00.0, rev: 209, irq: 17, latency: 32, mmio: 0xfbdff000
[   16.207586] saa7133[0]: subsystem: 5ace:7290, board: Beholder BeholdTV T7 [card=194,autodetected]
[   16.207601] saa7133[0]: board init: gpio is 0
[   16.208683] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \GP2C 1 (20131115/utaddress-251)
[   16.208690] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   16.208714] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   16.266670] device-mapper: multipath: version 1.6.0 loaded
[   16.267585] snd_hda_intel 0000:00:1b.0: irq 43 for MSI/MSI-X
[   16.270761] lp0: using parport0 (interrupt-driven).
[   16.292601] SKU: Nid=0x1d sku_cfg=0x4005e601
[   16.292604] SKU: port_connectivity=0x1
[   16.292605] SKU: enable_pcbeep=0x0
[   16.292606] SKU: check_sum=0x00000005
[   16.292607] SKU: customization=0x000000e6
[   16.292608] SKU: external_amp=0x0
[   16.292609] SKU: platform_type=0x0
[   16.292610] SKU: swap=0x0
[   16.292611] SKU: override=0x1
[   16.292937] autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[   16.292940]    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   16.292942]    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   16.292943]    mono: mono_out=0x0
[   16.292944]    inputs:
[   16.292946]      Rear Mic=0x18
[   16.292947]      Front Mic=0x19
[   16.292949]      Line=0x1a
[   16.292950]      CD=0x1c
[   16.292952] realtek: No valid SSID, checking pincfg 0x4005e601 for NID 0x1d
[   16.292954] realtek: Enabling init ASM_ID=0xe601 CODEC_ID=10ec0889
[   16.293804] EXT4-fs (sda3): re-mounted. Opts: errors=remount-ro
[   16.321488] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   16.321683] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[   16.322448] input: HDA Intel PCH Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[   16.322546] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[   16.322641] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[   16.322735] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[   16.338649] saa7133[0]: i2c eeprom 00: ce 5a 90 72 54 20 00 00 00 00 00 00 00 00 00 01
[   16.338658] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338665] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338672] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338678] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338684] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338691] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338698] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338704] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338711] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338718] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338724] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338731] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338737] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338744] saa7133[0]: i2c eeprom e0: a7 1f 01 00 ff ff ff ff ff ff ff ff ff ff ff ff
[   16.338751] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff
[   16.346918] tuner 9-0061: Tuner -1 found with type(s) Radio TV.
[   16.351272] xc5000: xc5000_attach(9-0061)
[   16.351276] xc5000 9-0061: creating new instance
[   16.359757] xc5000: XREG_PRODUCT_ID 2000
[   16.359760] xc5000: Successfully identified at address 0x61
[   16.359762] xc5000: Firmware has not been loaded previously
[   16.359767] xc5000: xc5000_config_tv() frequency=6400 (in units of 62.5khz)
[   16.366677] xc5000: xc5000_is_firmware_loaded() returns True id = 0x20
[   16.366682] xc5000: xc_set_signal_source(1) Source = CABLE
[   16.385414] xc5000: xc_set_tv_standard(0x8049,0x0c04)
[   16.385418] xc5000: xc_set_tv_standard() Standard = B/G-PAL-NICAM
[   16.397830] gpio_ich: GPIO from 180 to 255 on gpio_ich
[   16.434626] xc5000: xc_tune_channel(400000000)
[   16.434629] xc5000: xc_set_rf_frequency(400000000)
[   16.582585] xc5000: *** ADC envelope (0-1023) = 1540
[   16.590597] xc5000: *** Frequency error = 0 Hz
[   16.598588] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 2814
[   16.614583] xc5000: *** HW: V0.0, FW: V 0.0.0
[   16.622580] xc5000: *** Horizontal sync frequency = 7393 Hz
[   16.630580] xc5000: *** Frame lines = 980
[   16.638576] xc5000: *** Quality (0:<8dB, 7:>56dB) = 0
[   16.646576] xc5000: *** Unweighted analog SNR = 58 dB
[   16.654577] xc5000: *** Total gain = 211.80 dB
[   16.654585] xc5000: xc5000_config_tv() frequency=6400 (in units of 62.5khz)
[   16.662565] xc5000: xc5000_is_firmware_loaded() returns False id = 0x2000
[   16.908398] xc5000: firmware read 16497 bytes.
[   16.908401] xc5000: waiting for firmware upload (dvb-fe-xc5000c-4.1.30.7.fw)...
[   16.908402] xc5000: firmware uploading...
[   16.908403] xc5000: xc5000_tuner_reset()
[   17.306237] init: failsafe main process (708) killed by TERM signal
[   17.783118] Bluetooth: Core ver 2.17
[   17.783135] NET: Registered protocol family 31
[   17.783137] Bluetooth: HCI device and connection manager initialized
[   17.783145] Bluetooth: HCI socket layer initialized
[   17.783148] Bluetooth: L2CAP socket layer initialized
[   17.783152] Bluetooth: SCO socket layer initialized
[   17.785448] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   17.785452] Bluetooth: BNEP filters: protocol multicast
[   17.785459] Bluetooth: BNEP socket layer initialized
[   17.786746] Bluetooth: RFCOMM TTY layer initialized
[   17.786755] Bluetooth: RFCOMM socket layer initialized
[   17.786760] Bluetooth: RFCOMM ver 1.11
[   18.142200] init: cups main process (783) killed by HUP signal
[   18.142208] init: cups main process ended, respawning
[   19.206040] xc5000: Firmware upload complete...
[   19.238032] xc5000: xc_initialize()
[   19.569932] xc5000: Firmware dvb-fe-xc5000c-4.1.30.7.fw loaded and running.
[   19.569936] xc5000: xc_set_signal_source(1) Source = CABLE
[   19.585965] xc5000: xc_set_tv_standard(0x8049,0x0c04)
[   19.585973] xc5000: xc_set_tv_standard() Standard = B/G-PAL-NICAM
[   19.633933] xc5000: xc_tune_channel(400000000)
[   19.633938] xc5000: xc_set_rf_frequency(400000000)
[   19.899396] atl1c 0000:05:00.0: irq 44 for MSI/MSI-X
[   19.899946] atl1c 0000:05:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
[   20.170935] init: samba-ad-dc main process (814) terminated with status 1
[   20.365782] xc5000: *** ADC envelope (0-1023) = 368
[   20.373855] xc5000: *** Frequency error = 281 Hz
[   20.381759] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 2
[   20.397757] xc5000: *** HW: V6.0, FW: V 4.1.57374
[   20.405769] xc5000: *** Horizontal sync frequency = 15488 Hz
[   20.413753] xc5000: *** Frame lines = 65535
[   20.421765] xc5000: *** Quality (0:<8dB, 7:>56dB) = 0
[   20.429739] xc5000: *** Unweighted analog SNR = 0 dB
[   20.437738] xc5000: *** Total gain = 124.18 dB
[   20.445745] xc5000: *** PLL lock status = 0x0001
[   20.501722] Registered IR keymap rc-behold
[   20.501793] input: i2c IR (BeholdTV) as /devices/virtual/rc/rc0/input11
[   20.501858] rc0: i2c IR (BeholdTV) as /devices/virtual/rc/rc0
[   20.501860] ir-kbd-i2c: i2c IR (BeholdTV) detected at i2c-9/9-002d/ir0 [saa7133[0]]
[   20.502092] xc5000: xc5000_sleep()
[   20.502126] saa7133[0]: registered device video0 [v4l2]
[   20.502151] saa7133[0]: registered device vbi0
[   20.502173] saa7133[0]: registered device radio0
[   20.504150] WARNING: You are using an experimental version of the media stack.
[   20.504150] 	As the driver is backported to an older kernel, it doesn't offer
[   20.504150] 	enough quality for its usage in production.
[   20.504150] 	Use it with care.
[   20.504150] Latest git patches (needed if you report a bug to linux-media@vger.kernel.org):
[   20.504150] 	135f9be9194cf7778eb73594aa55791b229cf27c [media] dvb_frontend: start media pipeline while thread is running
[   20.504150] 	0f0fa90bd035fa15106799b813d4f0315d99f47e [media] cx231xx: enable tuner->decoder link at videobuf start
[   20.504150] 	9239effd53d47e3cd9c653830c8465c0a3a427dc [media] dvb-frontend: enable tuner link when the FE thread starts
[   20.504575] saa7134 ALSA driver for DMA sound loaded
[   20.504595] saa7133[0]/alsa: saa7133[0] at 0xfbdff000 irq 17 registered as card -2
[   20.504721] dvb_init() allocating 1 frontend
[   20.507068] xc5000: xc5000_config_tv() frequency=6400 (in units of 62.5khz)
[   20.508782] i2c i2c-9: Added multiplexed i2c bus 10
[   20.508786] si2168 9-0064: Silicon Labs Si2168 successfully attached
[   20.508799] xc5000: xc5000_attach(9-0061)
[   20.508801] xc5000 9-0061: attaching existing instance
[   20.513733] xc5000: xc5000_is_firmware_loaded() returns True id = 0x14b4
[   20.513738] xc5000: xc_set_signal_source(1) Source = CABLE
[   20.521735] xc5000: XREG_PRODUCT_ID 14b4
[   20.521741] xc5000: Successfully identified at address 0x61
[   20.521743] xc5000: Firmware has been loaded previously
[   20.521746] DVB: registering new adapter (saa7133[0])
[   20.521752] saa7134 0000:03:00.0: DVB: registering adapter 0 frontend 0 (Silicon Labs Si2168)...
[   20.549728] xc5000: xc_set_tv_standard(0x8049,0x0c04)
[   20.549733] xc5000: xc_set_tv_standard() Standard = B/G-PAL-NICAM
[   20.625738] si2168 9-0064: found a 'Silicon Labs Si2168-A30 build 2 id 0'
[   20.641728] xc5000: xc_tune_channel(400000000)
[   20.641733] xc5000: xc_set_rf_frequency(400000000)
[   20.648680] si2168 9-0064: downloading firmware from file 'dvb-demod-si2168-a30b2-01.fw'
[   21.369537] xc5000: *** ADC envelope (0-1023) = 476
[   21.385535] xc5000: *** Frequency error = 281 Hz
[   21.401526] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 2
[   21.433516] xc5000: *** HW: V6.0, FW: V 4.1.57374
[   21.449528] xc5000: *** Horizontal sync frequency = 15504 Hz
[   21.465541] xc5000: *** Frame lines = 65535
[   21.481505] xc5000: *** Quality (0:<8dB, 7:>56dB) = 5
[   21.497505] xc5000: *** Unweighted analog SNR = 63 dB
[   21.514095] xc5000: *** Total gain = 124.18 dB
[   21.529501] xc5000: *** PLL lock status = 0x0001
[   21.561600] xc5000: xc5000_config_radio() frequency=1400000 (in units of khz)
[   21.577493] xc5000: xc5000_is_firmware_loaded() returns True id = 0x14b4
[   21.577498] xc5000: xc_set_tv_standard(0x9002,0x0208)
[   21.577500] xc5000: xc_set_tv_standard() Standard = FM Radio-INPUT1
[   21.641473] xc5000: xc_set_signal_source(0) Source = ANTENNA
[   21.705465] xc5000: xc_tune_channel(87500000)
[   21.705470] xc5000: xc_set_rf_frequency(87500000)
[   22.017400] xc5000: xc5000_config_tv() frequency=6400 (in units of 62.5khz)
[   22.033385] xc5000: xc5000_is_firmware_loaded() returns True id = 0x14b4
[   22.033389] xc5000: xc_set_signal_source(1) Source = CABLE
[   22.065398] xc5000: xc_set_tv_standard(0x8049,0x0c04)
[   22.065404] xc5000: xc_set_tv_standard() Standard = B/G-PAL-NICAM
[   22.080466] vboxdrv: Found 4 processor cores.
[   22.080819] vboxdrv: fAsync=0 offMin=0x2c6 offMax=0x172a
[   22.080897] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   22.080899] vboxdrv: Successfully loaded version 4.3.26 (interface 0x001a000a).
[   22.161407] xc5000: xc_tune_channel(400000000)
[   22.161411] xc5000: xc_set_rf_frequency(400000000)
[   22.291700] vboxpci: IOMMU not found (not registered)
[   22.688320] init: plymouth-upstart-bridge main process ended, respawning
[   22.693182] init: plymouth-upstart-bridge main process (1739) terminated with status 1
[   22.693191] init: plymouth-upstart-bridge main process ended, respawning
[   22.897225] xc5000: *** ADC envelope (0-1023) = 532
[   22.913238] xc5000: *** Frequency error = 31 Hz
[   22.929239] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 2
[   22.961201] xc5000: *** HW: V6.0, FW: V 4.1.57374
[   22.977199] xc5000: *** Horizontal sync frequency = 15557 Hz
[   22.993196] xc5000: *** Frame lines = 65535
[   23.009189] xc5000: *** Quality (0:<8dB, 7:>56dB) = 5
[   23.025210] xc5000: *** Unweighted analog SNR = 63 dB
[   23.041183] xc5000: *** Total gain = 124.18 dB
[   23.057208] xc5000: *** PLL lock status = 0x0001
[   23.089308] xc5000: xc5000_sleep()
[   23.089330] xc5000: xc5000_sleep()
[   23.089453] xc5000: xc5000_sleep()
[   72.263241] si2168 9-0064: firmware download took 51628 ms
[   72.295234] si2168 9-0064: firmware version: 3.0.20
[   72.367217] xc5000: xc5000_sleep()
[  306.319704] xc5000: xc5000_init()
[  306.327703] xc5000: xc5000_is_firmware_loaded() returns True id = 0x14b4
[  306.439675] xc5000: *** ADC envelope (0-1023) = 368
[  306.447670] xc5000: *** Frequency error = 1023375 Hz
[  306.455671] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 2
[  306.471669] xc5000: *** HW: V6.0, FW: V 4.1.57374
[  306.479667] xc5000: *** Horizontal sync frequency = 15656 Hz
[  306.487662] xc5000: *** Frame lines = 559
[  306.495660] xc5000: *** Quality (0:<8dB, 7:>56dB) = 5
[  306.503661] xc5000: *** Unweighted analog SNR = 27 dB
[  306.511657] xc5000: *** Total gain = 124.18 dB
[  306.519656] xc5000: *** PLL lock status = 0x0001
[  306.527657] xc5000: xc5000_is_firmware_loaded() returns True id = 0x14b4
[  306.527660] xc5000: xc5000_set_digital_params() frequency=554000000 (Hz)
[  306.527662] xc5000: xc5000_set_digital_params() OFDM
[  306.527663] xc5000: xc5000_set_digital_params() frequency=554000000 (compensated to 551250000)
[  306.527665] xc5000: xc_set_signal_source(0) Source = ANTENNA
[  306.543654] xc5000: xc_set_tv_standard(0x800b,0x00c0)
[  306.543657] xc5000: xc_set_tv_standard() Standard = DTV8
[  306.575648] xc5000: xc_set_IF_frequency(freq_khz = 5000) freq_code = 0x1400
[  306.591640] xc5000: xc5000_tune_digital() setting OUTPUT_AMP to 0x8a
[  306.607638] xc5000: xc_tune_channel(551250000)
[  306.607640] xc5000: xc_set_rf_frequency(551250000)
[  307.235566] xc5000: *** ADC envelope (0-1023) = 640
[  307.243532] xc5000: *** Frequency error = 0 Hz
[  307.251529] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 1
[  307.267558] xc5000: *** HW: V6.0, FW: V 4.1.57374
[  307.275528] xc5000: *** Horizontal sync frequency = 15488 Hz
[  307.283554] xc5000: *** Frame lines = 65535
[  307.291523] xc5000: *** Quality (0:<8dB, 7:>56dB) = 5
[  307.299520] xc5000: *** Unweighted analog SNR = 63 dB
[  307.307550] xc5000: *** Total gain = 88.49 dB
[  307.315516] xc5000: *** PLL lock status = 0x0001
[  309.315110] xc5000 9-0061: Total Gain: -88dB (22654)
[  311.058784] xc5000 9-0061: Total Gain: -88dB (22654)
[  312.994383] xc5000 9-0061: Total Gain: -88dB (22654)
[  314.878009] xc5000 9-0061: Total Gain: -88dB (22654)
[  316.733623] xc5000 9-0061: Total Gain: -88dB (22654)
[  318.613219] xc5000 9-0061: Total Gain: -88dB (22692)
[  320.484837] xc5000 9-0061: Total Gain: -88dB (22692)
[  322.416466] xc5000 9-0061: Total Gain: -88dB (22692)
[  324.280095] xc5000 9-0061: Total Gain: -88dB (22692)
[  326.119726] xc5000 9-0061: Total Gain: -88dB (22692)
[  328.051337] xc5000 9-0061: Total Gain: -88dB (22692)
[  329.922951] xc5000 9-0061: Total Gain: -88dB (22692)
[  331.814573] xc5000 9-0061: Total Gain: -88dB (22692)
[  333.730184] xc5000 9-0061: Total Gain: -88dB (22692)
[  335.689745] xc5000 9-0061: Total Gain: -88dB (22692)
[  337.557401] xc5000 9-0061: Total Gain: -88dB (22692)
[  339.469019] xc5000 9-0061: Total Gain: -88dB (22692)
[  341.392630] xc5000 9-0061: Total Gain: -88dB (22692)
[  343.240249] xc5000 9-0061: Total Gain: -88dB (22692)
[  345.119843] xc5000 9-0061: Total Gain: -88dB (22692)
[  347.051465] xc5000 9-0061: Total Gain: -88dB (22692)
[  348.891090] xc5000 9-0061: Total Gain: -88dB (22692)
[  350.790764] xc5000 9-0061: Total Gain: -88dB (22692)
[  352.646330] xc5000 9-0061: Total Gain: -88dB (22692)
[  354.549954] xc5000 9-0061: Total Gain: -88dB (22692)
[  356.349591] xc5000 9-0061: Total Gain: -88dB (22692)
[  358.189248] xc5000 9-0061: Total Gain: -88dB (22692)
[  360.084811] xc5000 9-0061: Total Gain: -88dB (22692)
[  361.860477] xc5000 9-0061: Total Gain: -88dB (22692)
[  363.748096] xc5000 9-0061: Total Gain: -88dB (22692)
[  365.647742] xc5000 9-0061: Total Gain: -88dB (22692)
[  367.527326] xc5000 9-0061: Total Gain: -88dB (22692)
[  369.466908] xc5000 9-0061: Total Gain: -88dB (22692)
[  371.346551] xc5000 9-0061: Total Gain: -88dB (22692)
[  373.238159] xc5000 9-0061: Total Gain: -88dB (22692)
[  375.149745] xc5000 9-0061: Total Gain: -88dB (22692)
[  377.041392] xc5000 9-0061: Total Gain: -88dB (22692)
[  378.905013] xc5000 9-0061: Total Gain: -88dB (22692)
[  380.744609] xc5000 9-0061: Total Gain: -88dB (22692)
[  382.676253] xc5000 9-0061: Total Gain: -88dB (22692)
[  384.539840] xc5000 9-0061: Total Gain: -88dB (22692)
[  386.435529] xc5000 9-0061: Total Gain: -88dB (22692)
[  388.267119] xc5000 9-0061: Total Gain: -88dB (22692)
[  389.134881] xc5000: xc5000_sleep()
user@Andrey-Linux ~ $ 
